Open Access 4.0: Difference between revisions
Jump to navigation
Jump to search
(Created page with "==Open Access Control v 4.0== thumb This page contains documentation, installation tips and downloads for the all-new Open Access version 4. Open Ac...") |
|||
| (23 intermediate revisions by the same user not shown) | |||
| Line 13: | Line 13: | ||
*(1) Unsupervised tamper zone | *(1) Unsupervised tamper zone | ||
*(4) 5A relay outputs | *(4) 5A relay outputs | ||
*(2) 12V | *(2) 12V auxiliary power ports | ||
*Selectable USB output or direct-attach 3.3V UART to the Raspberry Pi | *Selectable USB output or direct-attach 3.3V UART to the Raspberry Pi | ||
*Real-time clock with battery backup (DS1307) | *Real-time clock with battery backup (DS1307) | ||
| Line 19: | Line 19: | ||
*Expansion header for CD or more inputs/outputs | *Expansion header for CD or more inputs/outputs | ||
===Support and Documentation=== | |||
<B>Quick Start Guide</B> | |||
* [[Open Access Quick Start Guide]] | |||
*[[Installing a Raspberry Pi Kit]] | |||
<B>Jumpers and settings</B> | |||
* [[Open Access v4 Jumpers]] | |||
<B>Electrical Specifications</B> | |||
* [[Open Access v4 Specs and Ratings]] | |||
<B>Schematics and Design Info</B> | |||
[[File:Open_Access_v4_schematic.pdf]] | |||
*Full set of schematics for the Open Access v4, in PDF format. | |||
<B>RFID Reader Documentation</B> | |||
* [[EM4100 Reader pinouts]] | |||
<BR> | |||
===Downloads=== | ===Software Downloads=== | ||
[[File: | <B>Firmware</B> | ||
*Latest firmware (v1. | [[File:Open_Access_Control_v4_std_140.zip ]] | ||
* | *Latest firmware (v1.40) for the Open Access v4 Hardware | ||
*Last build tested with Arduino 1.64 | |||
===Mounting Template=== | |||
*Mounting template for installing the Open Access v4 | *Mounting template for installing the Open Access v4 | ||
*Prints as actual size (approximately 4x6") | *Prints as actual size (approximately 4x6") | ||
[[File:Drill_template_v4.png|thumb|left]] | |||
[[File: | |||
Latest revision as of 10:30, 18 December 2015
Open Access Control v 4.0
This page contains documentation, installation tips and downloads for the all-new Open Access version 4. Open Access is a first-of-its-kind offering that brings enterprise security to the hobbyist, hacker and developer. The system is open-source and not encumbered by licensing, NDAs and other problems found with commercial hardware.
System Features
The Open Access Standand version 4 has an Arduino-compatible Atmega 328P on-board and support for powering and interfacing with the Raspberry Pi via it’s 26-pin header. Features include:
- Atmega328P with support for 200 local users in eeprom. Arduino compatible w/USB and ICSP programming.
- (2) Wiegand RFID reader ports with fused power, LED, and buzzer support
- (4) Supervised alarm zones
- (1) Unsupervised tamper zone
- (4) 5A relay outputs
- (2) 12V auxiliary power ports
- Selectable USB output or direct-attach 3.3V UART to the Raspberry Pi
- Real-time clock with battery backup (DS1307)
- Serial i2c EEPROM (Atmel AT24)
- Expansion header for CD or more inputs/outputs
Support and Documentation
Quick Start Guide
Jumpers and settings
Electrical Specifications
Schematics and Design Info File:Open Access v4 schematic.pdf
- Full set of schematics for the Open Access v4, in PDF format.
RFID Reader Documentation
Software Downloads
Firmware File:Open Access Control v4 std 140.zip
- Latest firmware (v1.40) for the Open Access v4 Hardware
- Last build tested with Arduino 1.64
Mounting Template
- Mounting template for installing the Open Access v4
- Prints as actual size (approximately 4x6")
